In that case, the threads within the tub spout or the pipeвЂ™s threaded adapter are likely stripped.Д¬orroded tub spouts or those covered in mineral deposits call for a slightly different approach. It doesnвЂ™t stay fixed in place and instead rotates freely on its axis. Or, perhaps the tub spout spins freely on the pipe. WD-40 may do the trick for stuck screw-in tub spouts. On the flip side, a set screw complicates things. For example, applying heat to a stuck slip-fit tub spout can be ideal for removing the stubborn fixture.

The best method for tackling stubborn tub spouts depends on the type of tub spout youвЂ™re dealing with. Unless youвЂ™re remodeling the entire bathroom or donвЂ™t mind moving the shower wall to fix broken plumbing, weвЂ™d recommend taking a different approach.

This is a great way to damage the plumbing. The worst thing you can do in these scenarios is use brute force to yank the tub spout off the pipe. Sometimes, the tub spout might be firmly fixed in place. Instead, refer to our troubleshooting section. Pull the tub spout straight out, sliding it off the pipe.ДЄgain, if there seems to be resistance, donвЂ™t force it. Once you loosen it, you can use your hand to finish turning the screw. You could reach underneath the tap and remove the screw or lay on your back in the tub to access the screw.Д®ither way, use the hex wrench to loosen the screw. Find a comfortable position to access the hex screw. On the other hand, if you have a Moen slip-fit tub spout, youвЂ™ll need a 5/32-inch hex wrench. Instead, jump down to the troubleshooting section. If it doesnвЂ™t give pretty easily, there might be corrosion or mineral deposits.ДonвЂ™t force it, as you might damage the plumbing. Use a cloth underneath the wrench to cover and protect the finish. If you canвЂ™t get a good grip on the spout, use an adjustable wrench or strap wrench to hold the fixture firmly. To remove this type of tub spout, unthread it by turning it counterclockwise. The spout itself threads directly onto the exposed plumbing. You shouldnвЂ™t need any special tools to remove a threaded (IPS) Moen tub spout. If you donвЂ™t (and you decide to lay on your back in the tub to remove the spout), you might end up on the receiving end of a sudden shower. If it is, no worries вЂ“ weвЂ™ll guide you through removing stubborn tub spouts later on.ДЄs with nearly any plumbing project, make sure you turn off the water supply to the tub. It should only take a few minutes, providing the fixture isnвЂ™t bound by corrosion or mineral deposits. Removing a Moen tub spout, whether itвЂ™s a CC spout or an IPS spout, is pretty straightforward. Or, use your fingers to feel for a screw hole in the underside of the spout. The screw is in an awkward position, so you might have to lay on your back in the tub to look for one.

If youвЂ™re not sure what kind of tub spout it is, look on the underside of the spout for a screw. Because Moen only has two different configurations, removing the spout should be a reasonably straightforward task. They thread directly onto the exposed piece of pipe protruding from the wall, and thereвЂ™s no hex screw holding it in place. MoenвЂ™s IPS tub spouts are a kind of threaded tub spout. Usually, these tub spouts fit onto a ВЅ inch copper pipe. They slide directly onto the exposed plumbing, then are held in place by a small hex screw in the underside of the spout. CC tub spouts are a type of slip-fit tub spout. Moen designs tub spouts in two different ways: CC and IPS.

How Do You Remove A Stubborn Tub Spout?.